BodyCraft Home Gym MA605LP User Manual

INSTRUCTION MANUAL  
LEG PRESS OPTION FOR STRATA STRENGTH  
TRAINING SYSTEM  
QUESTION?  
As a quality home gym supplier we are committed to your complete satisfaction. If you have questions,  
or find missing or damaged parts, we will guarantee your complete satisfaction through our authorized  
dealer service centers or our home office customer service department. Please call your local dealer  
for assistance or RSI at 800-990-5556 (9:00 AM - 5:00 PM). Our trained technicians will provide  
immediate assistance to you, free of charge.  
We stand behind our products. Every piece, every part of this BODYCRAFT strength training system  
is guaranteed for as long as you own it. We will repair or replace anything that goes wrong.  
Bodycraft is a division of Recreation Supply Inc.  
P.O. BOX 181  
Sunbury, OH 43074  
 
PARTS LIST  
NO.  
DESCRIPTION  
QTY.  
201  
202  
203  
204  
205  
206  
207  
208  
209  
210  
211  
212  
213  
214  
215  
216  
217  
218  
219  
220  
221  
222  
223  
224  
225  
226  
227  
228  
229  
230  
231  
232  
233  
234  
235  
236  
237  
238  
239  
240  
84A  
BASE CONNECTION  
FRONT BASE  
1
1
1
1
2
1
1
1
1
1
1
4
15  
2
1
8
1
4
8
2
2
2
4
2
3
2
2
4
12  
2
18  
6
9
1
1
3
1
1
2
1
1
LEG PRESS SUPPORT  
REAR TUBE  
SLIDING SEAT SUPPORT FRAME  
SEAT SUPPORT  
SLIDING TUBE  
FOOT REST  
STEEL ROLLER  
HANDLE BAR  
SINGLE PULLEY BRACKET  
50 ID. SQUA. END CAP  
50 SQUA. END CAP  
RUBBER STOP  
RUBBER BUMPER  
NON-SKID PAD  
SPRING PIN  
3/4" STEEL BUSHING  
1/2" STEEL BUSHING  
1/2" X 7" HEX HEAD BOLT  
1/2" X 3-1/2" HEX HEAD BOLT  
1/2" X 3-1/8" HEX HEAD BOLT  
3/8" X 3" HEX HEAD BOLT  
3/8" X 2-1/2" HEX HEAD BOLT  
3/8" X 2" HEX HEAD BOLT  
3/8" X 1" HEX HEAD BOLT  
3/8" X 3/4" HEX HEAD BOLT  
5/16" X 1/2" SETSCREW  
1/2" WASHER  
3/8" WASHER(LARGE)  
3/8" WASHER(SMALL)  
1/2" NYLON NUT  
3/8" NYLON NUT  
LEG PRESS CABLE  
HOOK  
PULLEY  
SEAT  
BACK PAD  
1" X 130 HAND GRIP  
OWNER'S MANUAL  
TOP CABLE (2890 mm)  
1
 
PARTS CHART  
REAR TUBE(204)  
BASE  
CONNECTION(201)  
FRONT  
BASE(202)  
SEAT SUPPORT(206)  
SLIDING TUBE(207)  
SLIDING SEAT  
SUPPORT FRAME(205)  
STEEL  
ROLLER(209)  
SINGLE PULLEY  
BRACKET(211)  
LEG PRESS SUPPORT(203)  
HANDLE BAR(210)  
FOOT REST(208)  
3/4" STEEL  
RUBBER  
STOP(214)  
1/2" STEEL  
BUSHING(219)  
HOOK(235)  
BUSHING(218)  
1" x 130  
HAND GRIP(239)  
SEAT(237)  
BACK PAD(238)  
SPRING PIN(217) PULLEY(236)  
LEG-PRESS CABLE (234) (2030 mm)  
TOP CABLE(84A) (2890 mm)  
FASTENER  
5/16" X 1/2"  
SETSCREW(228)  
1/2" NYLON NUT(233)  
3/8" NYLON NUT(234)  
1/2" WASHER(229)  
3/8" X 2-1/2" HEX HEAD BOLT(224)  
1/2" X 3-1/2" HEX HEAD BOLT(221)  
3/8" WASHER(LARGE)(230) 3/8" WASHER(SMALL)(231)  
0"  
1/2"  
1"  
1-1/2"  
2"  
2-1/2"  
3"  
3-1/2"  
4"  
4-1/2"  
5"  
5-1/2"  
6"  
6-1/2"  
7"  
2
 
STEP1  
1.Attach BASE CONNECTION(201) and FRONT BASE(202) to the holes in the  
LEFT WEIGHT BASE of Bodycraft Strata home gym using two 1/2" x 3-1/8" HEX  
HEAD BOLT(222), four 1/2" WASHER(229) and two 1/2" NYLON NUT(232).  
2.Attach LEG PRESS SUPPORT(203) to FRONT BASE(202) using two 3/8" x 3"  
HEX HEAD BOLT(223), four 3/8" WASHER(SMALL)(231) and two 3/8" NYLON  
NUT(232).  
Attach REAR TUBE(204) to LEG PRESS SUPPORT(203) as shown using two  
3/8" x 3" HEX HEAD BOLT(223), four 3/8" WASHER(SMALL)(231) and two 3/8"  
NYLON NUT(232).  
213  
201  
LEFT WEIGHT BASE  
232  
229  
201  
232  
213  
203  
212  
213  
233  
229  
222  
LEFT WEIGHT BASE  
233  
231  
231  
202  
223  
231  
223  
212  
233  
212  
231  
231  
204  
223  
212  
3
 
STEP2  
To ensure best performance, lubricate all pivot points during assembly.  
Insert two 3/4" STEEL BUSHING(218) and four 1/2" STEEL BUSHING(219)  
to SLIDING SEAT SUPPORT FRAME(205).  
Attach SLIDING SEAT SUPPORT FRAME(205) to LEG PRESS SUPPORT(203)  
as shown using two STEEL ROLLER(209) as shown.  
Tighten 5/16" X 1/2" SETSCREWS(228) with Hex Wrench to bolt STEEL ROLLERS  
(209) in place.(See FIG B)  
Attach eight NON-SKID PAD(216) to FOOT REST(208).  
Attach SEAT SUPPORT(206) to SLIDING SEAT SUPPORT FRAME(205) as  
shown using two 1/2" x 3-1/2" HEX HEAD BOLT(221), four 1/2" WASHER(229)  
and two 1/2" NYLON NUT(232)  
Attach FOOT REST(208) to SLIDING SEAT SUPPORT FRAME(205) as shown  
using two 1/2" x 7" HEX HEAD BOLT(220), four 1/2" WASHER(229) and two  
1/2" NYLON NUT(232).  
213  
213  
218  
218  
219  
216  
205  
219  
208  
218  
218  
220  
213  
229  
229  
232  
229  
232  
229  
FIG B  
228  
208  
228  
203  
209  
205  
209  
205  
FIG A  
213  
203  
227  
214  
229  
230  
230  
214  
221  
229  
206  
213  
227  
229  
232  
207  
217  
206  
4
 
STEP3  
Attach HANDLE BAR(210) and SEAT(237) to SEAT SUPPORT(206) as shown  
using two 3/8" X 1" HEX HEAD BOLT(226) and two 3/8" WASHER(231).  
Attach BACK PAD(238) on SEAT SUPPORT(206) as shown using two 3/8" x 2-1/2"  
HEX HEAD BOLT(224) and two WASHER(SMALL)(231).  
CHECK that all the parts are in assembled correctly as drawing then  
tighten all bolts. Attach all plastic ends caps and grips to appropriate  
places.  
239  
210  
239  
238  
237  
231  
224  
206  
210  
226  
226 231  
5
 
LEG PRESS CABLE  
LEG PRESS CABLE(234)  
If previously installed, completely remove TOP CABLE(84), along with pulleys T1, T2,  
T3, T4 and T5. Remove the two bolts and attach the TOP BEAM into the FRONT  
UPRIGHT. Assemble TOP CABLE(84A) (from leg press box) and pulleys simultaneously.  
Insert threaded end of TOP CABLE(84A) into slot in front of TOP BEAM, over pulleys  
T1, T2, around pulley T3, and over T4. Run threaded end of TOP CABLE(84A) through  
SINGLE PULLEY BRACKET(211) and attach pulley G1 as shown. Finish by routing TOP  
CABLE(84A) over pulley T5 and attach threaded end of TOP CABLE(84A) into SELECTOR  
ROD. For safety reasons, the threaded end should be screwed in using at least half of  
the available screw length. The jam nut should be tightened to SELECTOR ROD to  
prevent loosening. Replace the two bolts that attach the TOP BEAM to the FRONT  
UPRIGHT and tighten. Make certain the TOP CABLE(84A) runs above these bolts.  
Attach RUBBER BUMPER(215) to top of SINGLE PULLEY BRACKET(21).  
TOP CABLE(84A)  
T2  
T1  
T4  
T5  
84A  
T5  
75  
51  
80  
9
84A  
77  
90  
51  
65  
T3  
L5  
75  
FLOATING PULLEY BLOCK(32)  
TOP  
CABLE(84A)  
T2  
T1  
T4  
P2  
T5  
AB  
T3  
L5  
CABLE(86)  
A2  
T3  
L5  
L7  
LOWER  
CABLE(87)  
G1  
LOWER  
CABLE(87)  
84A  
211  
A2  
L7  
T3  
234  
L5  
6
 
Screw thread end of LEG PRESS CABLE(234) into SINGLE PULLEY BRACKET(211).  
Attach pulleys G2 and G3, making certain LEG PRESS CABLE(234) runs beneath  
pulleys and is scated in pulley grooves. Attach the eyelet cable end to  
ADJUSTMENT TUBE(207) as shown.  
G1  
234  
G1  
211  
201  
231  
G2  
225  
231  
G3  
202  
233  
207  
236  
234  
G2,G3  
236  
231  
225  
233  
234  
201,202  
235  
207  
225  
206  
7
 
Assembly is complete! Please take the following steps before using the gym:  
1. Make certain all bolts are tightened securely.  
2. Make certain all cables are seated into all pulley grooves. A cable rubbing against  
steel will peel the nylon coating, voiding warranty and resulting in a need for  
replacement.  
3. Pre-stretch the cables. Put the Weight Selector Pin (37) in the bottom hole on the  
weight stack. Pull on the cables with great force, helping remove any kinks and  
providing any initial cable stretch.  
4. Be aware the cables can loosen and slightly stretch upon initial use.  
5. The cables should be adjusted as tight as possible, but no so tight as to lift the Top  
Plate (82) above the weight stack. Be certain to secure the jam nuts after  
adjustments are made.  
6. For better performance, apply a household lubricant (such as silicone) to any  
adjustable areas and to the Guide Rods (8 ).  
7. Enjoy many years of a Fit Lifestyle!  
Thank you for purchasing the Bodycraft Strata Home Gym. If you have any  
questions, please call your local Bodycraft dealer or call our customer service  
department at 800-990-5556.  
 

BenQ Projector MP625P User Manual
BenQ Projector MS614 User Manual
Black Decker Grinder G950 User Manual
Blodgett Oven COS 20G User Manual
Blue Rhino Charcoal Grill CBT702WB C User Manual
Bosch Appliances Welding System LBB 3588 User Manual
Bushnell Binoculars 11 0512 User Manual
Cambridge Audio Stereo Amplifier Azur 840EW User Manual
Chief Manufacturing Indoor Furnishings FTR Series User Manual
Cisco Systems Camcorder Ultra2HD User Manual