Brady Label Maker Brady Worldwide Identification Solutions User Manual

DSP-5  
Brady Worldwide Identification Solutions  
6555 West Good Hope Road  
P.O. Box 2131  
Milwaukee, WI 53201-2131  
Phone: (800) 537-8791  
Fax: (800) 292-2289  
05/01  
 
SET-UP INSTRUCTIONS  
ADJUSTMENTS  
Hold Down Brush:  
Using 5/32" (4mm) hex wrench, adjust reel holder arm to vertical.  
Using the upper thumbscrew on the side of the machine, adjust the hold down brush for  
tensioning.  
Place the label roll on the 1" (25mm) reel hanger bar.  
*If roll has 3" (76.2mm) core, use plastic spool*  
Slide “O” ring onto reel hanger bar to hold roll against reel holder arm to ensure it is  
held straight.  
For best results, labels should be pressed firmly against the strip plate. If labels are held  
too tightly, they will cause excessive drag on the motor.  
Photosensor:  
(Hex wrench, O-ring and spool included.)  
The photosensor can be adjusted in any direction to accommodate virtually any label.  
Loosening the lower thumbscrew allows the photosensor to swivel and sets the overhang  
distance of the label over the strip plate. When the label is being fed the correct  
distance, tighten the lower thumbscrew.  
Thread the liner under the guide rod, between the hold down brush and the strip plate,  
then back under the strip plate. Lay the liner across the slot in the take-up hub. Slide the  
lock rod into the slot to secure the liner. Align shaft collar on guide rod with edge of  
liner to keep material feeding straight.  
Loosen the two screws on the front of the sensor holder to align the photosensor with  
the center of the label. If there are two or more labels across, align the photosensor  
with the last label to be removed. When these two screws are tightened, the machine  
is set.  
Reel Holder Arm  
Positioning of Photosensor  
Incorrect  
Hold Down Brush  
Guide Rod  
Lock Rod  
Reel Hanger Bar  
Sensor sees beyond label  
- Will not stop  
Sensor sees strip plate  
- Will not feed  
Strip Plate  
Correct  
Photosensor  
Take-up Hub  
Sensor sees front edge of label  
4
5
 
FEATURES  
MAINTENANCE  
• Will dispense butt-cut and die-cut material.  
• Adjustable photosensor for pinpoint accuracy.  
• Handled lock rod makes scrap removal easy.  
• No tools required for adjustment.  
Turn machine off when not in use. Remove liner material from take-up hub at  
approximately 3" in diameter or if motor appears to be straining. Do not operate  
machine without covers in place. Do not operate if inspection reveals a damaged  
power or sensor cord.  
LEGEND  
Model DSP-5  
NOTES  
• Keep strip plate free of adhesive build-up.  
• Clean photosensor with compressed air or dry cloth.  
• Do not drop the dispenser or subject it to heavy shock.  
Turn off machine when not in use.  
Item #  
Part #  
1
NV50008  
1A  
1B  
2
NV50008-1  
NV50008-2  
NV50010  
2A  
2B  
3
NV50010-1  
NV50010-2  
NV50017  
REPAIR POLICY  
Contact BRADY CORPORATION to determine nature of problem.  
3A  
4
NV50017-1  
NV50017-2  
NV-SPOOL  
Furnish Brady with the following information:  
1. Who the unit was purchased from.  
2. Model number and serial number.  
3. Date purchased (copy of invoice or packing slip required).  
5
6
NV50001A (115V)  
NV50001C (220V)  
NV50001-1  
NV50018-2  
NV50013A  
6A  
6B  
7
Brady will issue an RGA (Return Goods Authorization) for repair.  
Return machine to Brady by UPS, insured and prepaid.  
Brady will notify the customer if there is a repair charge.  
8
NV50012  
8A  
9
NV50012-1  
NV50014-1  
NV50014-3  
NV50014  
9A  
10  
10A  
NV50017-1  
SPECIFICATIONS:  
11  
NV50026B  
NV50011-2  
NV50026-1  
NV50026A  
NV50015  
NV50017-1  
NV50015A  
NV50011A  
NV50002A  
NV50011  
11A  
11B  
12  
Model#  
DSP-5  
Liner Capacity  
Width  
.25" to 4.5"  
13  
(6.35mm to 115mm)  
13A  
13B  
14  
Label  
.125" to 7"  
Length  
(3.2mm to 178mm)  
15  
16  
Roll Capacity  
Feed Speed  
12" (30.5mm)  
16A  
16B  
17  
NV50011-2  
NV50011-1  
NV50007  
1.3" / sec*  
(3.3mm / sec.)  
18  
NV50003  
19  
NV50009  
Dimensions  
Inches  
19A  
20  
NV50007-1  
NV50021 (115V)  
NV50021A (220V)  
NV50005-1  
NV50021-1  
NV50019  
10.8 (L) x 10.8 (W) x 14.5 (H)  
Centimeters 27.4 (L) x 27.4 (W) x 36.8 (H)  
20A  
20B  
21  
Weight  
10.5 lb. (4.76 kg.)  
Electrical  
117V 50/60Hz, <1 amp  
(220V 50/60Hz available)  
21A  
22  
NV50019F  
NV50018C  
NV50005  
NV50005-1  
NV50021-1  
Requirements  
23  
*at start-up  
23A  
23B  
6
3
 

Beko Washer WMA 620 S User Manual
Belkin Power Supply F6C1000 TW RK User Manual
Bosch Appliances Home Security System DINION 4000 AN User Manual
Bose Flat Panel Television 46 User Manual
Brother All in One Printer DCP 7010L User Manual
Bushnell Binoculars 26 2024 User Manual
Carrier Air Compressor 5F User Manual
Cascade Speaker System 3C User Manual
Chief Manufacturing Mobility Aid CM2C40 User Manual
Chromalox Electric Heater S RAD 2 User Manual